|
 |
Similar Items |
 |
|
Item # U-2330-25W |
Dare Wood Post Tape Insulator
- Holds tape 1" from post
- Grips tape tightly to prevent whipping and sawing
- Tape holder unlocks to aid installation
- Nails included
- White, Pack of 25
|
|
| |
|
Item # U-IWTNY-RS |
Red Snap’r Polytape Insulator
- Extends tape 2" from the post
- Tape holder unlocks for easy installation
- Nails included
- Yellow, pack of 25
|
|
| |
|
Item # GRL4 |
1 5⁄8" Tube Gate
- 50" height
- Hot-dip galvanized after fabrication
- Includes hardware kit
|
|
| |
|
Item # GRW4 |
Mesh Wire Gate
- 50" height
- 2" x 4" mesh spacing
- Hot-dip galvanized after fabrication
|
|
| |
|
Item # MGK5 |
Grounding Kit
- Includes 3 rods, 3 clamps and 50ft of wire
- Convenient package for easy grounding set up
|
|
| |
|
Item # PD80 |
Kencove PD80 Post Driver
- Drives posts up to 7⅛" diameter X 10' tall
- 30,000 pounds of impact at full stroke
- Manual tilt: 15-degree front-back/15-degree side-side
- Hydraulic requirements: 3-4 GPM @ 1,500 PSI
- Includes 3-point hitch and secure-stand base
|
|
| |
|
Item # PD8S |
Spring 8/16
- For use with HD8 or HPD16 post driver
- Includes spring ends
|
|
| |
|
Item # PGD2875 |
Titan PGD2875
- Powerful and portable gas-powered driver
- Powered by 1.2 horsepower, 4-stroke engine
- 3¼" barrel
- Drives posts up to 3" in diameter
- Includes 1" and 2" adapter sleeves for posts smaller than 2"
- Weighs 28 pounds
|
|
| |
|
Item # RB2 |
Stafix X-Braid, ¼"
- 8 conductors for maximum conductivity
- Heavy-duty braid for maximum strength
- Ideal for long lengths of semi-permanent fence
|
|
| |
|
Item # RO8 |
Electric Rope 1/3" Diameter White
- Large diameter provides exceptional visibility
- Strong, durable, and excellent conductivity
- UV-stabilized for maximum weather resistance
- 6 stainless-steel conductors
|
|
| |
|
Item # U-MB60 |
Powerfields MB60
- 12-volt battery energizer
- 0.40 output joules
- Includes ground rod
|
|
| |
|
Item # WRH4W |
HotTop® Plus Fence Rail 4¼"
- Combines the beauty of rail fence with the safety of electric
- No painting, peeling, or rusting
- Strength and flexibility is ideal for horses
|
|
| |
|
Item # GSCS |
Extra Spring
- Galvanized for longevity
- Use with 14 ft spring gate (GSC)
|
|
| |
|
Item # PD80H |
Kencove PD80H Post Driver
- Drives posts up to 7⅛" diameter X 10' tall
- 30,000 pounds of impact at full stroke
- Hydraulic tilt: 15-degree front-back/15-degree side-side
- Hydraulic requirements: 3-4 GPM @ 1,500 PSI
- Includes 3-point hitch and secure-stand base
|
|
| |
|
Item # U-IW5XNB-RS |
Red Snap’r 5” Wood Post Extender
- 5" offset
- Two large shields prevent shorting
- Easy 45-degree front end loading
- NOT FOR USE with polytape or high-tensile wire
- Nails included
- Black, pack of 25
|
|
| |
|
Item # VJXV2 |
Jobe Vortex Float Valve
- Mounting: horizontal or vertical
- Pressure range: 5-100 PSI
- Max flow: 2" - 300 GPM
|
|
| |
|
Item # PDSHD8 |
Kencove PD8 Post Driver
- Drives posts up to 7⅛" diameter X 10' tall
- 30,000 pounds of impact at full stroke
- Manual tilt: 15-degree front-back/15-degree side-side
- Hydraulic requirements: 3-4 GPM @ 1,500 PSI
|
|
| |
|
Item # CHRC |
Hog Rings 11⁄16"
- Attach plastic deer net to high tensile guide wire
- Use with Economy Hog Ring Gun (THGC) 11⁄16"
- 16 gauge galvanized steel
|
|
| |
|
Item # GL1 |
KIWI One Way Latch
- One-handed operation
- Prevents gate sagging
- Fits gates with 1 5/8" - 2" round tube
|
|
| |
|
Item # GMA1 |
Fuse
- For use with Kencove and Speedrite energizers
|
|
| |
|
Item # PDSHD8H |
Kencove PD8H Post Driver
- Drives posts up to 7⅛" diameter X 10' tall
- 30,000 pounds of impact at full stroke
- Hydraulic tilt: 15-degree front-back/15-degree side-side
- Hydraulic requirements: 3-4 GPM @ 1,500 PSI
|
|
| |
|
Item # PTC |
Safe-T-Post Cap
- Protects animals from sharp edges
- Increases visibility
- Durable uv-resistant material
|
|
| |
|
Item # U-G382504 |
Gallagher M1000 Energizer
- 110-volt, plug-in energizer
- 7.5 output joules
- Ideal for large pastures
- Low-impedance
- Features a voltage bar graph with digital output reading
|
|
| |
|
Item # WG18 |
Zinc/Aluminum, 180 KSI, 12½ Gauge
- Class 3 Zinc/Aluminum-coated high-tensile
- Hand knot or crimp
- Ideal for all perimeter fences
- Minimum break strength = 1,385 lbs
|
|
| |
|
Item # WM6 |
210 KSI, 16 Gauge
- Class 3 galvanized high-tensile
- Polished electroplate
- Ideal for interior electric fences
- Minimum break strength = 614 lbs
|
|
| |
|
Item # WRH5W |
HotTop® Plus Fence Rail 5¼"
- Combines the beauty of rail fence with the safety of electric
- No painting, peeling, or rusting
- Strength and flexibility is ideal for horses
|
|
| |
|
Item # WRHEB4BL |
HotTop® Plus Pre-Bent Buckle
- Installed on large diameter end posts
- Hot-dipped galvanzied and powder coated
- Insulating grommet, washer and screws included
|
|
| |
|
Item # WSR5W |
HorseRail® 5.25"
- Three 12.5 gauge wire core
- Doesn't rust and never needs painted!
- Thirty year limited manufacturers warranty
|
|
| |
|
Item # HMSS |
Mini Spring -Stainless
- Use with twine, ribbon, or aluminum wire
- Stainless steel
- Designed for low tension applications
|
|
| |
|
Item # MSP10-20MB |
Solar Panel Mounting Bracket
- For use with 10-20 watt solar panel
- Preformed hanger allows one-person installation
- Mounting hardware included
|
|
| |
|
Item # PD12S |
Spring 12⁄24
- For use with HD12 or HPD24 post driver
- Includes spring ends
|
|
| |
|
Item # WL6 |
Soft Wire, 16 Gauge
- Class 3 galvanized soft wire
- 16 gauge
- Preloaded on a wooden payout reel
- Easy to repair and retighten
|
|
| |
|
Item # WRHEB4BR |
HotTop® Plus Pre-Bent Buckle
- Installed on large diameter end posts
- Hot-dipped galvanzied and powder coated
- Insulating grommet, washer and screws included
|
|
| |
|
Item # WSR6W |
HorseRail®6.25"
- Three 12.5 gauge wire core
- Doesn't rust and never needs painted!
- Thirty year limited manufacturers warranty
|
|
| |
|
Item # DNC8 |
Monofilament, 8 Gauge
- Ideal for reinforcing deer net
- Sold by the foot -buy only the length you need!
- High strength and easy to handle
|
|
| |
|
Item # GLA |
KIWI Gate Anchor
- Hold gate open in any position
- Prevents gate end from sagging or swinging
- For use with 1 5/8" - 2" tube gates
|
|
| |
|
Item # ITPCW |
T-Post Cap Insulator
- Use with polytape up to 1 1/2" wide, wire or rope up to 1/2" diameter
- UV protected to resist weathering
- Pack of 10
|
|
| |
|
Item # PDSHD10H |
Kencove PD10H Post Driver
- Drives posts up to 8¾" diameter X 10' tall
- 71,500 pounds of impact at full stroke
- Hydraulic tilt: 15-degree front-back/15-degree side-side
- Hydraulic requirements: 12 GPM @ 1,500 PSI
|
|
| |
|
Item # RRSC |
1:1 Value Reel
- Holds up to 1,640' twine or 656' ribbon
- 1:1 gear ratio
- Built-in wire guide
|
|
| |
|
Item # DNC10 |
Monofilament 10 Gauge
- Use to support or reinforce plastic netting
- Ideal for vineyard trellis applications
- High strength and easy to handle
|
|
| |
|
Item # GNZLC |
Chain Gate Hook - Economy
- One-handed operation
- Spring-loaded locking ring and quick-link
- Galvanized hook and chain
|
|
| |
|
Item # MPS |
Power-Surge Protector
- Economical protection from power spikes/surges
- Indicator light shows status
- Protects from surges up to 6000v
|
|
| |
|
Item # PDSHD12 |
Kencove PD12 Post Driver
- Drives posts up to 10⅛" diameter X 10' tall
- 100,000 pounds of impact at full stroke
- Hydraulic tilt: 20-degree front-back/25-degree side-side
- Hydraulic requirements: 5 GPM @ 2,000 PSI
|
|
| |
|
Item # PT5PG |
HD Painted T-Post
- Made from heavy duty rail steel
- High gloss baked enamel paint
- Proudly made in USA
|
|
| |
|
Item # RRPY |
Step-In Post Yellow
- Holds twine, ribbon or 4 lines of tape up to 1.6" wide
- Extended, reinforced steel spike
- EZ-Clip system with 8 spacing options
|
|
| |
|
Item # TEP |
EzePull 4-in-1 Fence Tool
- Crimps all 12.5 gauge sleeves
- Hardened stainless steel jaws
- Wire cutter, crimper, staple puller, cable stripper
|
|
| |
|
Item # U-ITTW-RS |
Red Snap’r T-Post Polytape Insulator
- Fits standard t-posts
- Use with polywire, polytape, polyrope, steel wire, and aluminum wire
- Tape holder unlocks for easy installation
- Made in the USA
- Pack of 25
|
|
| |
|
Item # WBL2D |
200 KSI, 12½ Gauge
- Class 3 galvanized high-tensile
- Works best with crimp sleeves
- Ideal for all perimeter fences
- Minimum break strength = 1,540 lbs
- Painted black
|
|
| |
|
Item # WRHTA4W |
HotTop® Plus Adjustable T-Buckle
- For use with 4.25" HotTop Plus fence
- Hot-dip galvanized and powder coated
- Ideal for use at junctions or cross fence
|
|
| |
|
Item # U-YBSTP25N |
Zareba Reverse T-Post Insulator
- Claw-style insulator
- Fits standard t-posts and u-posts
- Use with polywire, polyrope, steel wire, and aluminum wire
- Snap-on, reversed design
- Yellow, pack of 25
|
|
| |
|
Item # U-816067-25 |
Patriot 2" T-Post Extender
- Available in 2" and 5" offsets
- Reversible design fits back and front of t-posts
- Works with high-tensile, polywire, or ½" polytape
- For permanent or temporary fences
|
|
| |
|
Item # U-817204-25 |
Patriot 5" T-Post Extender
- 5" offset
- Fits standard t-posts
- Quick, easy installation
- Excellent arcing protection to reduce shorting
|
|
| |
|
Item # U-IT5XB-RS |
Red Snap'r 5" T-Post Extender
- 5" offset
- Fits standard t-posts
- Wraparound design ensures secure hold
- Not for use with polytape
- Black, pack of 25
|
|
| |
|
Item # DNC12.5 |
Monofilament 12½ Gauge
- Works well to support or reinforce deer net
- Minimum break strength = 250 lbs
- Sold by the foot
|
|
| |
|
Item # JTP |
T-Post Tape Insulator
- Accommodates up to 1.5" electric tape
- Fits t-post sizes 1 1/2 - 1 3/8"
- Pack of 25
|
|
| |
|
Item # SDZ |
Solid Zinc Cog Tightener
- Solid Zinc cog
- Tensioning with a crescent, box or open end wrench
- Wider cog holds more wire
|
|
| |
|
Item # U-EA5M-BL |
Blitzer EA5M-BL
- 110-volt, plug-in energizer
- 0.10 output joules
- Low-impedance
- Ideal for dogs, poultry, and rabbits
|
|
| |
|
Item # U-EDC15M-BL |
Blitzer EDC15M
- 12-volt battery operation
- 1.0 output joule
- Works with all types of fence
- Ideal for areas with no access to AC power
|
|
| |
|
Item # U-PT25RP |
Rod Post Polytape Insulator
- Fits rod posts ranging from ¼" - ⅝" diameter
- Self-centering post cavity with spin-on nut
- Holds up to 1½" wide tape
- Pack of 25
|
|
| |
|
Item # U-8555B |
Blitzer 8555-B
- 115-volt, high-impedance fence charger
- Use with short-haired animals and pets, steel wire, and aluminum wire
- Not for use with tape, twine, or electric netting
|
|
| |
|
Item # U-G330414 |
Gallagher Wrangler
- 110-volt, plug-in energizer
- 1.0 stored joule
- Indicator light flashes with every pulse
- Low-impedance
|
|
| |
|
Item # U-YIRB-RS |
Red Snap'r Rod Post Insulator
- Fits ¼" to 9⁄16" diameter rod posts
- Can be used with all fence wire and rope
- Easy, 45-degree front-end loading feature
- Black, pack of 25
|
|
| |
|
Item # U-G328504 |
Gallagher M150
- 110-volt, plug-in energizer
- 1.5 output joules
- Controls up to 60 acres or 11 miles of fence
- Ideal for small pastures
|
|
| |
|
Item # GSR |
Electric Bungy Cord Gate
- Safer and more visable than spring gates
- Cord stretches to twice its length
- Includes gate hook up set
|
|
| |
|
Item # U-PW50 |
Power Wizard PW50
- 110-volt, plug-in energizer
- 0.05 output joules
- Low-impedance
- Ideal for pest control
|
|
| |
|
Item # U-PW250B |
Power Wizard PW250B
- DC-powered energizer
- 12-volt battery not included
- 0.25 output joules
- Low-impedance
|
|
| |
|
Item # U-PW350B |
Power Wizard PW350B
- DC-powered energizer
- 12-volt battery not included
- 0.35 output joules
- Low-impedance
|
|
| |
|
Item # GH15 |
Tube Gate Hinge Clamp
- Hot-dip galvanized
- Fits 3/4" hinge bolts
- For use with 1.5" and 2" heavy duty tube gates
|
|
| |
|
Item # PV4CRS |
Vector Model 4 Post Driver w/ Rock Spike
- Drives posts up to 12' tall and up to 12" diameter
- 130,000 pounds of impact at full stroke
- 840-pound solid steel hammer
- Includes rock spike with swing arm
|
|
| |
|
Item # PVV |
Vector Utility Model Post Driver
- Drives posts of any height in almost any terrain
- 90,000 pounds of impact at full stroke
- 530-pound solid steel hammer
|
|
| |
|
Item # VJDA |
Jobe Detach Tail
- Replacement tail for Detach system
- Use with Megaflow or Topaz valves
|
|
| |
|
Item # VJPM |
Protect-A-Mount
- Use with ¾" Topaz or Rojo valves
- Quickly mounts valve on tank
- Provides protection from all animals
- Fits most style tanks
|
|
| |
|
Item # VJVDB |
Jobe Valve Base
- Use with ¾" and 1" Megaflow Valves
- Replacement Megaflow Valve Detach Base
|
|
| |
|
Item # GHBX |
12" Locking Gate Bolt
- Ideal for long or heavy gates
- Extra shaft to secure bolt to post
- Hot-dip galvanized
|
|
| |
|
Item # VJDFN |
Pilot Flow Filter
- Allows some debris to flow through without plugging
- Use with ¾" - 1" Megaflow or Topaz valves
|
|
| |
|
Item # NSLT120-MB60 |
Electric Netting Kit
- 32" high, 120' long electric net
- 0.4-joule, 12-volt energizer
- Ground rod
- Battery not included
|
|
| |
|
Item # VJVG |
Plastic Gasket for Jobe Valves
- Use with ¾" Megaflow, Rojo, or Topaz valves
- Low-density polyethelene replacement washer
- Fits between tail and backnut
|
|
| |
|
Item # TCTGC |
Cable Cutters
- Spring-loaded handle
- Ideal for cutting cable, rope or twine
|
|
| |
|
Item # CG1 |
Gripple 1
- Use to terminate 15 - 11 gauge wire
|
|
| |
|
Item # CGS |
Gripple Small
- Simple and effective way to join or tension wire
- Use with 17 to 13 gauge mild wire
- Patented ceramic locking mechanism
|
|
| |
|
Item # CGWT |
Gripple Twister
- Wraps around wire end to prevent injury
- Use with 14 - 10 gauge wire
|
|
| |
|
Item # CWBTE |
Discolored Two-Bolt Rope Clamp
- DISCOLORED POWDER COATING
- Versatile, 2¼" connector
- Can be used as a splicer where an opening is occasionally needed
- Powder-coated steel
- High-quality product with unattractive powder coating
|
|
| |
|
Item # DB4 |
Earth Anchor 40
- Galvanized
- Use to hold down a lifting post
- Easily installed
|
|
| |
|
Item # DB4DR |
Drive Rod
- 1/4" x 2'
- Use with DB4 earth anchor
|
|
| |
|
Item # DB6DR |
Drive Rod
- 36" x ½" diameter
- Use with DB6 earth anchor
- Hardened, machined, steel rod
|
|
| |
|
Item # DB8I |
Earth Anchor 88
- Use to hold down a lifting post
- 3000lb hold
- Galvanized cast iron
|
|
| |
|
Item # F12-4D |
1⁄2" FiberRod SunGuard
- Pre-drilled every 2 inches
- Coated to prevent splintering
- Will not rust, rot or crack due to cold
|
|
| |
|
Item # F1Q |
FiberRod 1.25"
- 1¼" diameter fiberglass rod
- B-grade, uncoated
- Self-insulating
- Custom cut to desired length
|
|
| |
|
Item # F1R |
1" FiberRod Sucker
- 1" diameter fiberglass rod
- B-grade, uncoated
- Self-insulating
- Custom cut to desired length
- Economical
|
|
| |
|
Item # FP1 |
Dropper Clip 1"
- Use with PasturePro Fence Droppers
- Rustfree stainless steel
- Easy to install!
|
|
| |
|
Item # G05 |
Insultube
- Use as undergate wire or insulate jumper wires
- .16" ID, .36" OD
|
|
| |
|
Item # GCCB |
Economy Gate Handle
- Galvanized expansion spring
- Allows for movement with gate posts
- Attaches with hook
- Made of UV-stabilized plastic
|
|
| |
|
Item # GCCW |
Economy Gate Handle
- Galvanized expansion spring
- Allows for movement with gate posts
- Attaches with hook
- Made of UV-stabilized plastic
|
|
| |
|
Item # GCNW |
Economy Spring Gate Handle
- Economy plastic gate handle
- For use with spring gates
- Spring gate easily attaches to handle
- Made of UV-stabilized plastic
|
|
| |
|
Item # GD82 |
Lead Out Wire (Double)
- 2 heavily insulated soft galvanized steel wires
- Protective white sheath
- Designed for direct burial
|
|
| |
|
Item # GLW |
Universal Gate Latch
- Attaches to tube and mesh gate up to 1-5/8"
- Simple to open
- Unique locking feature
- Padlock feature
- Corrosion resistant
|
|
| |
|
Item # GXC |
Cattle Panel
- Hot-dip galvanized after fabrication
- 6" x 8" wire spacing
- Ideal for use with t-posts
|
|
| |
|
Item # HB2 |
2" Double-Barbed Staples
- Class 3 galvanized
- Double barbed for superior hold
- Approximately 48 staples per pound
|
|
| |
|
Item # HBM |
1½" Double-Barbed Staple
- Class 3 galvanized
- Double barbed for superior hold
- Approximately 66 staples per pound
|
|
| |
|
Item # HW6 |
Wedge-Loc 60 Socket
- Holds t-post in place when used for diagonal brace
- Use to brace wooden posts with t-posts
- Solid rust-free Aluminum
|
|
| |
|
Item # HW9 |
Wedge-Loc 90 Socket
- Holds t-post in place when used for diagonal brace
- Use to brace wooden posts with t-posts
- Solid rust-free Aluminum
|
|
| |
|
Item # I71 |
Steel Y Post Insulator
- Pack of 25
- Accommodates high-tensile wire or electric twine
- Large spark guard prevents arching
|
|
| |
|
Item # ICLOFFSET |
Chain-link Insulator
- Extends wire 4.5" from post
- Use with chainlink fence or attach to t-post
|
|
| |
|
Item # ISW |
Snug Wood Post Insulator
- Fast and easy to install
- Wire held 1" from post
- UV inhibitor
- Nails included
- Flexible base fits round or flat posts
|
|
| |
|
Item # J16W |
Flip Top Insulator
- For use with tape up to 1.6" wide
- Convenient flip-top secures fence tape
- UV-resistant plastic resists weathering
|
|
| |
|
Item # JR55W |
Tee Tensioner
- For use at cross junctions of electric tape
- Quick and easy to use
|
|
| |
|
Item # JRPW |
Rod Post Tape Insulator
- For use with up to 1.5" electric tape
- 2 large shields to prevent shorting
- UV-stabilized to resist weathering
|
|
| |
|
Item # JWPW |
Wood Post Tape Insulator
- Accommodates tape up to 2" wide
- UV-protected plastic resists weathering
- Made in USA
|
|
| |
|
Item # KPD5TH4 |
4.5" Standard Auger Head
- For use with 4.5" auger flight
- Ideal for hard soil or soft rock
- Easily replaceable carbide tipped teeth
|
|
| |
|
Item # KPDAB |
Auger Bearing
- For use with standard Kiwi auger system
|
|
| |
|
Item # KPDBDH4 |
4.5" Blue Demon Head
- Uses 5 replaceable carbide insert bits
- Ideal for abrasive cutting conditions
- Heavy-duty casting head
|
|
| |
|
Item # KPDSS |
KIWI Skid-Steer Post Driver
- Drives all types of wood or steel posts
- 120,000 pounds of impact at full stroke
- 50-degree side-side and front-back tilt
- Hydraulic requirements: 15 GPM @ 1,500 PSI
|
|
| |
|
Item # KPDT3P |
KIWI Tractor-Mounted Post Driver
- Drives all types of wood or steel posts
- 120,000 pounds of impact at full stroke
- 48" side slide
- 50-degree side-side and front-back tilt
- Hydraulic requirements: 15 GPM @ 1,500 PSI
|
|
| |
|
Item # MFC |
K-CLIPS®
- Stainless steel
- Use to secure warning signs or fence flags
- Attach to any gauge wire or electric twine
|
|
| |
|
Item # MSG |
Storm Guard
- Easy to use and install
- Protects charger from lightning
- Use with chargers with 1 joule or greater output
|
|
| |
|
Item # NRP |
28" Electric Netting Post
- Split-top post to allow re-positioning
- Foot pedal and steel spike for easy installation
- Use for extra support in uneven terrain
|
|
| |
|
Item # NSGPW |
NSG/NSPC Extra Post
- For use with 40" electric nets
- Use for extra support in uneven terrain
- Steel step-in pedal for easy installation
|
|
| |
|
Item # PD100SS |
Kencove PD100SS Post Driver
- Drives posts up to 8¾" diameter X 10' tall
- 71,500 pounds of impact at full stroke
- Manual tilt: 15-degree front-back/15-degree side-side
- Hydraulic requirements: minimum 12 GPM @ 1,500 PSI
- Includes skid-steer mounting bracket and secure-stand base
|
|
| |
|
Item # PD80HSS |
Kencove PD80HSS Post Driver
- Drives posts up to 7⅛" diameter X 10' tall
- 30,000 pounds of impact at full stroke
- Hydraulic tilt: 15 degree front-back/15 degree side-side
- Hydraulic requirements: 3-4 GPM @ 1,500 PSI
- Includes skid-steer mounting bracket and secure-stand base
|
|
| |
|
Item # PD80SS |
Kencove PD80SS Post Driver
- Drives posts ties up to 7⅛" diameter X 10' tall
- 30,000 pounds of impact at full stroke
- Manual tilt: 15 degree front-back/15 degree side-side
- Hydraulic requirements: 3-4 GPM @ 1,500 PSI
- Includes skid-steer mounting bracket and secure-stand base
|
|
| |
|
Item # PDN1000 |
Nitro 1000 Post Driver
- Powered by nitrogen
- Minimal maintenance
- Safest driver on the market
- Available for skid-steer or excavator
|
|
| |
|
Item # PDN750 |
Nitro 750 Post Driver
- Powered by nitrogen
- Minimal maintenance
- Safest driver on the market
- Available for skid-steer or excavator
|
|
| |
|
Item # PP1.25X6W |
PasturePro Post 1.25" x 6'
- Wood-plastic composite flexes on impact
- Lightweight, yet extremely durable
- Self-insulating and easily drilled
|
|
| |
|
Item # PP1.5X6W |
PasturePro Post 1.5" x 6'
- Wood-plastic composite flexes on impact
- Lightweight, yet extremely durable
- Self-insulating and easily drilled
|
|
| |
|
Item # PP1.5X7W |
PasturePro Post 1.5" x 7'
- Wood-plastic composite flexes on impact
- Lightweight, yet extremely durable
- Self-insulating and easily drilled
|
|
| |
|
Item # PP1X4W |
PasturePro Dropper 1" x 4'
- Self-insulating, wood-plastic composite
- Lightweight, yet extremely durablee
- Won't rot, rust, or crack
|
|
| |
|
Item # PPPD |
Pilot Driver
- Perfect for tough, rocky soil
- Steel spike and large handles
- Creates a 1" pilot hole
- Use with PasturePro composite posts
- Creates a 1" pilot hole
|
|
| |
|
Item # RPPS |
45" Stirrup Post
- 45" total length
- Top clip holds the fence 38" above the ground
- 2 clips for 1½" wide polytape and 6 clips for rope, wire, and narrow polytape
- 7" metal spike
|
|
| |
|
Item # RTT |
Twist-Tight Tensioner
- Use with light gauge wire, twine or hot ribbon
- Easily take up slack in any portable fence line
|
|
| |
|
Item # TCTXL |
Knipex 9⅞" Wire Cutters
- 9⅞" handles provide more leverage
- Operate with two hands for maximum cutting force
- Induction-hardened cutting edges and chrome-vanadium, heavy-duty steel
- Made in Germany.
|
|
| |
|
Item # TDBS |
Square Head Drive Bit
- #2 square drive bits
- For use with 1.75" stainless steel screws
- 2 per pack
|
|
| |
|
Item # TFDR |
Rapid Tightener
- Fast and easy to use
- Use with EZ-Daisy strainers
|
|
| |
|
Item # TFP |
Fence Pliers
- Great for cutting soft wire
- Hammer head and staple puller
|
|
| |
|
Item # TMWE |
Economy Measuring Wheel
- 12½" diameter wheel
- Reads up to 10,000'
- Foldable handle
- Great value for large fence projects or contractors
|
|
| |
|
Item # U-A-71B |
Fi-Shock Line Tightener
- Tightener for electric fence
- Tightens polywire, ½ polytape, and wire up to 9 gauge
- No tools required
|
|
| |
|
Item # U-EAC25M-BL |
Blitzer EAC25M-BL
- 110-volt, plug-in energizer
- 1.0 output joules
- Controls up to 25 miles of fence
- Low-impedance
- Ideal for horses, cattle, sheep, llamas, pigs, and predator control
|
|
| |
|
Item # U-G344404 |
Gallagher S17
- Solar-powered operation
- 0.8 output joules
- Equipped with 1.5-watt solar panel
- Low-impedance
- Weather-proof case
- Internal, rechargeable battery included
|
|
| |
|
Item # U-G503014 |
Gallagher Digital Voltmeter
- Monitors fence voltage and helps trace fence line shorts and faults
- Reads voltage for battery energizers
- Uses one 9-volt battery
- Pocket size
|
|
| |
|
Item # U-G627014 |
Gallagher Double-Insulated Cable
- 65'
- Suitable for under-gate wire
- Softer outer layer for easier stripping
- Suitable for initial lead-out lengths
- 12½ gauge galvanized wire
|
|
| |
|
Item # U-I-31 |
Power Wizard T-Post Topper
- Rubber t-post topper
- Covers top of t-post to reduce injury to your animals
- White, pack of 25
|
|
| |
|
Item # U-I-5 |
Power Wizard Safety Top and Tape Insulator
- Use with polytape up to 1½" polywire, steel wire, or aluminum wire
- Fits standard t-posts
- May be installed facing front, back, right, or left
- Grips tape tightly to prevent whipping and sawing
- Protects valuable livestock from sharp, jagged t-post tops
- UV-stabilized
- White, pack of 10
|
|
| |
|
Item # U-P-3C |
Fiberglass Post End Cap
- Black fiberglass post end caps
- Prevent splintering the end of fiberglass rods
|
|
| |
|
Item # U-WC-100 |
Fi-Shock 17 Gauge Wire
- 100' of galvanized, 17 gauge wire
- Basic, economical wire for electric fence
- 125-145 lbs break strength
- Tensile strength of 90,000-105,000 PSI
|
|
| |
|
Item # U-WP25N |
Red Snap'r Wood Post Claw Insulator
- Pin-lock wood post insulator for high-tensile fence
- Removable pin-lock holds wire securely
- 2-nail installation (nails included)
- Made from UV-stabilized, high-density polyethylene
- Black, pack of 25
|
|
| |
|
Item # U-WPX25N |
Red Snap'r 5" Wood Post Extender
- 5" offset
- For use on wood posts
- Can be used with all gauges of wire
- Not for use with high-tensile
- One-nail installation (nails included)
|
|
| |
|
Item # VCR |
Quick-Coupler Riser
- One-handed operation
- Use in above ground or buried water systems
|
|
| |
|
Item # VCTMA |
Jobe Tank Mount Adapter
- Use to mount a float valve in a tank with a garden hose connection
- ¾" pipe thread to ¾" hose thread
- Max pressure: 150 PSI
- Swivel end for garden hose to eliminates twisting the hose while tightening
|
|
| |
|
Item # VFA |
Fence-Alarm
- Provides real-time updates to your mobile phone via text or email
- Works with any brand of fence energizer
- Can be placed anywhere along your fence
- Includes ground rod, hookup wires, connection clamps, and a 6-volt battery
- One year of free fence monitoring protection
|
|
| |
|
Item # WEBF4W |
Flat End Buckle
- Galvanized and powder coated
- Designed to attach HorseRail to posts in dips/rises in terrain
|
|
| |
|
Item # WL4SF |
Soft Wire, 14 Gauge
- Class 3 galvanized soft wire
- 14 gauge
- Preloaded on plastic spool or wooden payout reel
- Easy to repair and retighten
|
|
| |
|
Item # WM2CW |
Coated Wire -Unbonded
- High visibility and safety
- Unbonded for easier stripping-splicing
- Made in USA
|
|
| |
|
Item # WSB4W |
Splicer Buckle
- Join two sections of HorseRail quickly
- Galvanized and powder coated for longevity
|
|
| |
|
Item # WSBT4W |
Top Bracket
- Use to attach top line of rail to wood post
- Galvanized and powder coated
|
|
| |
|
Item # WSSS5W |
5.25" Split Spooler
- Use on existing Horserail fence
- Maintains tension on fence line
- Galvanized and powder coated
|
|
| |
|
Item # WSSS6W |
6.25" Split Spooler
- Use on existing Horserail fence
- Maintains tension on fence line
- Galvanized and powder coated
|
|
| |
|
Item # WTT12SF |
Aluminum Fence Wire, 14 Gauge
- Ideal for electric fence
- Preloaded on plastic spool or wooden payout reel
- Rustproof wire can last up to 50 years
- Easy to repair and retighten
- .08" diameter
|
|
| |
|
